Hey Bobby, awesome job. What a great document. Thanks!!
Heated Seat Issue
- Thread starter Arm
- Start date
Help Support BMW i3 Forum:
Hey Bobby, awesome job. What a great document. Thanks!!
groovyboovy
Member
- Joined
- Mar 23, 2019
- Messages
- 10
What a hero, I have a heated seat problem, switches off after a short while and will be following this guide to try to fix it, cheers
Can you please report back as to the result?
groovyboovy
Member
- Joined
- Mar 23, 2019
- Messages
- 10
Today I followed the guide, found 2 broken wires and fixed he problem, hurray for the maker of the guide (BobbyC).
To add to the guide this took me about 4 hours, including lunch/ test drive and tidying up all my tools etc. Page 9 I did not need to cut the 2 metal fastening ring clips, I was able to unclip them off the bar then after clip them back over it again.
I lengthened the broken grey and black wires and routed them over the metal bar, when re-assembling everything I broke the very thin yellow wire and had to solder it on again.
It is a really good hint to measure the resistance, on page 3 before dis-assembling.
I did undo the 4 bolts to take the seat out to make it easier to look underneath, but did not take it out (as it looks like it has an air bag in it), I was able to give it a good vacuum and found nearly £1 in change and amint, so I am up on the job to, same could happen for you.
Rob
To add to the guide this took me about 4 hours, including lunch/ test drive and tidying up all my tools etc. Page 9 I did not need to cut the 2 metal fastening ring clips, I was able to unclip them off the bar then after clip them back over it again.
I lengthened the broken grey and black wires and routed them over the metal bar, when re-assembling everything I broke the very thin yellow wire and had to solder it on again.
It is a really good hint to measure the resistance, on page 3 before dis-assembling.
I did undo the 4 bolts to take the seat out to make it easier to look underneath, but did not take it out (as it looks like it has an air bag in it), I was able to give it a good vacuum and found nearly £1 in change and amint, so I am up on the job to, same could happen for you.
Rob
awesome job! I have experience taking apart VW seats as some of the heating elements were on the cushion and integrated into the covers as well. I am not looking forward to doing the sam on the i3. Not sure what I can do to prevent the eventual wear spots. But thanks for sharing
ECStuning has some nice photosJust finished replacing my driver's seat cushion and have some observations and pictures to share. My seat heater was coming on fine but would turn off after 3 min and will not turn on until the car is turned off and on, and a few minutes have passed. I had a broken temperature sensor. I believe if yours comes on and goes off after only a few seconds this is an indication that you have a broken heating element not the sensor. They both require same part and work to replace - just replace the seat cushion with the heater & sensor integrated (assuming the seat not the back is the problem) - part # 52-10-7-388-647 - Seat Cushion Pad Left for driver seat. Cheapest OEM I found was at my local dealer who is selling parts online with local pick up - total cost $170. https://www.thebmwminipartstore.com/
I used the Youtube video referred on the first page of this thread for instructions - work is not hard - taking the seat off the car is much easier that other seats I've worked on since it is lighter and the lack of B-pillar helps a lot. Taking the cushion out is not hard but annoying and time consuming. I think it's best to get a good cutter and just cut the metal clamps as they will be very hard to reuse. Just get two dozens of small plastic ties - they work very well - this is what the guy in the Youtube video does too. Threading the ties under the seat cushion wire is hard initially but as you progress it becomes easy. Just make sure you orient them so that you'd be able to tighten and cut them as you progress in the assembly process.
To get the seat off the car you need to disconnect the seat power supply - this is very easy but if the car is not completely off it will trigger an airbag warning that needs a special tool to erase. I wasn't worried about this as I do have the tool - I just turned the car off but when the door is open the instrument cluster has the BMW logo on it. After I put the seat back and reconnected everything the airbag warning was triggered and I had to clear it. I believe you'd have to wait for the car to go into sleep or remove the battery to make sure the warning is not triggered if you don't have a tool to clear it.
I peeled the heater off the cushion where the temperature sensor sits on my old cushion just to see where the problem was. I took some pictures that might be helpful if someone wants to fix it rather than buy a new cushion - it seems an easy fix in my case. If I have to do it again I would first try to fix mostly because I like to revive thigs rather than throwing them away. The guy in the Youtube video shows how to measure the resistance of the heaters to diagnose the problem. There are three wires coming out of the plug - brown, green/purple, and black. The green/purple splits into green and gray before it gets into the cushion - the green one goes to the heater, the gray one to the sensor - this picture shows the wires:
https://photos.app.goo.gl/4YQayW368aRC9zBu5
I measured the resistance of the new cushion at the plug between the black and green/purple - it was around 10 kOhms, bad one was zero as the black wire was broken. Here is where I had to peel the heater pad to get to the sensor:
https://photos.app.goo.gl/2TCMmKpKUsyo2chX8
Here is the sensor from underneath the pad - the sensor is still inside the pad - you can see the two yellow wires leading to it:
https://photos.app.goo.gl/vHyxqwGiAT6Mky7RA
And here is where my black wire was broken:
https://photos.app.goo.gl/tmzfJ2sMP1fvwP5f7
This must be a weak spot as you can see that the gray wire has the insulation broken too. It seems it would be easy to replace these with new pieces of wire.
Hope this helps others to diagnose and fix these problems. Cheers.
https://www.ecstuning.com/b-genuine-bmw-parts/left-seat-foam-plastic-part/52107388647/
Bobby,
Did you consider relocating the temp sensor behind and towards the edge of the seat closest to the center console? This way, it avoids the metal rod altogether? Not going under OR over?
Last edited:
groovyboovy
Member
- Joined
- Mar 23, 2019
- Messages
- 10
An auto electrician should be able to fix it like this, but may not be able to give you any sort of guarantee
Thank you for posting this document, even if I think implementing it may be over my head. I just started experiencing the problem I've heard several others mention, where my seat heater turns on, then shuts off after 5 seconds or so and won't stay on after that no matter what I do. The passenger side works fine. At least I've got something to try to see if I can fix it myself rather than let it go, because I can imagine what any BMW shop will charge me to fix it and I refuse to pay it.
Dat komt helaas wel vaker voor, het kabeltje is standaard te kort.
That happens often as the cable is too short by default. Maybe losing some weight might prevent this in the future.
Similar threads
